Pit Boss Auger Motor Not Turning: Reasons and Solutions!

If the auger motor on your Pit Boss auger motor not turning, there are a few things you can check to troubleshoot the issue.

First, make sure that the Pellet Hopper Lid is closed tightly and that there is no debris blocking the auger motor. Next, check to see if the Pellet Auger Drive Belt is tight and free of any damage. If the belt looks damaged or loose, it will need to be replaced. Finally, make sure that the Pellet Grill Power Switch is turned on and that there is power running to the unit.

If all of these things check out and the auger motor still isn’t turning, you may need to replace the motor itself.

Pit Boss Auger Motor Not Turning- Solve Here!

If you have a Pit Boss Pellet Grill, you may have experienced problems with the auger motor. This is a common issue that can be caused by several different things. In this blog post, we’ll take a look at some of the most common causes of auger motor problems and what you can do to fix them.

One of the most common causes of auger motor problems is simply age and wear and tear. Over time, the gears in the motor can become worn down, making it harder for the motor to turn. If your grill is more than a few years old, it’s likely that this is the cause of your problem.

The good news is that replacing the gears in your auger motor is relatively easy and inexpensive – it’s just a matter of finding the right replacement parts. Another common cause of auger motor problems is debris getting lodged in the gears. This can happen if you use your grill frequently and don’t clean it out regularly.

When grease and food particles build up on the gears, they can start to bind together and make it difficult for the motor to turn. The best way to prevent this from happening is to make sure you clean your grill thoroughly after each use. You can also try using a brush or other tool to remove any built-up debris from the gears before you start grilling again.

If you’re still having trouble with your auger motor after trying these tips, there are a few other things you can check before calling customer service or taking your grill back to the store.

First, make sure that all of the connections are tight and secure – sometimes loose wires can cause intermittent issues with motors like this.

Second, check for any obvious damage or corrosion on the outside of the motor – if something looks damaged, it’s probably best not to try fixing it yourself but rather takes it back to where you bought it so they can deal with it appropriately.

Finally, if all else fails, resetting your grill might do trick – consult your owner’s manual for instructions on how to do this properly.

Pit Boss Auger Motor Bracket:

Pit Boss Auger Motor Not Turning

If you have a Pit Boss pellet grill, you may eventually need to replace the auger motor. The auger is what feeds pellets into the fire pot, and the motor turns the auger to keep the pellets moving. Replacing the motor is not a difficult task, but it’s one that requires a bit of knowledge about your grill.

The first thing you’ll need to do is remove the hopper lid and empty out any remaining pellets. Next, use a Phillips head screwdriver to remove the four screws that hold the motor in place. Be careful not to lose these screws, as they are specific to the Pit Boss brand.

With the old motor removed, take a look at how it was wired up. You’ll need to connect the new motor in the same way. Once you have everything hooked up, simply screw the new motor into place and reattach the hopper lid.

Turn on your grill and test out your new auger motor! If all goes well, you should be back in business and grilling up tasty food in no time flat.

Pit Boss Auger Motor Upgrade

If you have a Pellet Grill or Smoker that uses a Pit Boss Auger Motor, then you know how important it is to keep that motor running smoothly. Over time, the auger motor can start to wear down and eventually fail. When this happens, it’s time to consider an upgrade.

There are a few different options available when it comes to upgrading your Pit Boss auger motor. One option is to simply replace the existing motor with a new one. This is often the most cost-effective option and can be done fairly easily if you have some basic mechanical skills.

Another option is to upgrade to a more powerful auger motor. This will provide your grill or smoker with more consistent performance and may even help extend its life overall. If you do decide to go this route, be sure to research which motors are compatible with your specific model of grill or smoker before making your purchase.

Finally, you could also consider upgrading the entire auger assembly itself. This would include both the motor and the auger housing unit. While this is usually the most expensive option, it can also provide the best overall performance and longevity for your grill or smoker.

No matter which option you choose, upgrading your Pit Boss auger motor is a great way to keep your pellet grill or smoker running like new for years to come!

Pit Boss Replacement Auger Motor:

Pit Boss Replacement Auger Motor

If your Pit Boss smoker isn’t working correctly, one possible issue is the auger motor. The auger motor is responsible for moving the wood pellets from the hopper to the fire pot, and if it’s not working properly, your smoker will have trouble igniting or maintaining a consistent temperature. Fortunately, replacing the auger motor is a relatively easy process that you can do yourself with just a few tools.

To replace the auger motor, first, make sure that there is no power going to the smoker. Then, remove the hopper lid and Pellet Dump Tray Assembly by unscrewing the four screws that hold it in place. Next, disconnect the two wires that lead from the control panel to the auger motor one black and one red.

Finally, remove the three screws that secure the auger motor to its bracket and lift it out of place. Now you can install your new Pit Boss Replacement Auger Motor by reversing these steps. Be sure to connect the wires correctly – black to black and red to red – before screwing everything back into place.

Once you’ve done this, your smoker should be working like new again!

Pit Boss Auger Assembly:

Pit Boss Auger Assembly: If you’re looking for a top-quality auger assembly for your Pit Boss smoker, look no further than our selection at Smoker Parts Depot. We carry a wide variety of Pit Boss auger assemblies to choose from, so you’re sure to find the perfect one for your needs.

Our augers are made from high-quality materials and are designed to provide years of trouble-free use. When it comes time to replace your Pit Boss auger assembly, be sure to check out our selection at Smoker Parts Depot. We carry a wide variety of Pit Boss auger assemblies to choose from, so you’re sure to find the perfect one for your needs.

Our augers are made from high-quality materials and are designed to provide years of trouble-free use.

Frequently Asked Questions (FAQs):

Why is My Auger Not Turning on My Pit Boss?

If your auger is not turning on your Pit Boss, there are a few potential reasons why. Here are the most common reasons why an auger might not turn on:
1. The switch is turned off – Check to make sure that the switch is in the “on” position.
2. There is no power – If there is no power going to the Pit Boss, then the auger will not turn on. Check to make sure that the power cord is plugged in and that there is power coming from the outlet.
3. The fuse has blown – If there is a fuse in the circuit, it may have blown. Replace the fuse with a new one and see if that fixes the problem.
4. The motor isn’t working – If none of the above solutions work, then it’s likely that the motor itself isn’t working properly.

How Do You Unstick an Auger on a Pit Boss?

If your auger is stuck, there are a few things you can do to try and unstick it. First, check the manual that came with your Pit Boss for any specific instructions on how to unstick an auger. If there are none, don’t worry – we’ve got you covered. Here are a few tips:
1. Use a pair of pliers or a wrench to loosen the set screw that holds the auger in place. This may take some force, so be careful not to strip the set screw.
2. Once the set screw is loosened, you should be able to twist the auger counter-clockwise if it’s stuck clockwise or clockwise if it’s stuck counter-clockwise. Keep twisting until the auger comes free.
3. If step 2 doesn’t work, try using a pair of vice grips or another similar tool to grip onto the end of the auger shaft and twist it until it comes free. Again, be careful not to strip anything.
4. If all else fails, you can always call customer service for assistance. They may have additional tips or tricks that can help get your auger unstuck!

How Do You Know If Your Auger is Jammed?

If your auger is jammed, you won’t be able to turn it. You’ll need to disassemble the auger to clear the jam.

How Do You Prime Auger on Pit Boss?

If you’ve never used a Pit Boss before, priming the auger may seem like a daunting task. But don’t worry – we’ll walk you through it step by step so that you can get started using your new smoker as soon as possible. The first thing you need to do is make sure that your Pit Boss is properly assembled.

Once everything is in its place, open up the hopper and fill it with pellets. We recommend using only one type of pellet for your first few smokes, so that you can get a feel for how they burn. Next, locate the igniter button on the control panel.

This is usually located near the bottom of the panel, and it will have a small red light next to it. Press and hold the igniter button for 3-5 seconds. You should hear the auger start to turn, which means that it’s drawing pellets into the fire pot.

Once you see smoke coming from the exhaust stack, you can release the igniter button. At this point, all you need to do is close the lid and let your Pit Boss do its thing!

Conclusion

If your Pit Boss auger motor isn’t turning, there are a few things you can try to fix the problem. First, make sure that the power cord is plugged in securely and that the outlet it’s plugged into is working. If the cord and outlet are both fine, then check to see if the circuit breaker has tripped.

If it has, reset it and try again. If none of these solutions work, then you may need to replace the auger motor.

Robert Dennis

I am Robert Dennis - A professional grill and smoker technician, I have over 10 years of experience in the industry. I am skilled in the repair and maintenance of all types of grills and smokers and am knowledgeable in the use of a variety of tools and techniques. I share my knowledge and experience to help readers understand the inner workings of grills and smokers and how to maintain them properly. I am dedicated to providing the best information to help readers keep their grills and smokers in top working condition. - Serve Yourself -

Leave a Reply