Hey there! This post contains affiliate links to products. We may receive a commission for purchases made through these links. But it never influences our product selection process.
The Traeger auger is designed to turn when there is food in the hopper that needs to be fed into the fire pot. However, if the motor isn’t working properly, the auger may not turn. If your auger isn’t turning, check to make sure that there is food in the hopper and that the motor is turned on.
Does the Traeger Auger Always Turn?
The short answer is no, the Traeger auger does not always turn. The auger is designed to turn on and off intermittently to maintain the desired temperature in the grill. When the grill needs to be heated, the auger will turn on and feed pellets into the firepot until the desired temperature is reached. Once the temperature is reached, the auger will turn off until the grill needs to be heated again.
Why is the Auger Turning Off Important?
It’s important for the Traeger auger to turn off intermittently because it prevents the grill from getting too hot. If the auger were to continuously feed pellets into the firepot, the grill would continue to get hotter and hotter until it reached dangerous levels. By turning off intermittently, the auger ensures that the grill stays at a safe and consistent temperature.
What Happens if the Auger Doesn’t Turn?
If the Traeger auger doesn’t turn, it can cause issues with the grill’s performance. If the auger doesn’t turn on when it’s supposed to, the grill won’t heat up properly, and you won’t be able to cook your food. If the auger doesn’t turn off when it’s supposed to, the grill can get too hot and potentially cause a fire.
Troubleshooting: How to Clear a Jammed Auger
Traeger’s auger is designed to turn when there is food in the hopper and to stop when the hopper is empty. However, sometimes the auger can get stuck in the “on” position, causing it to continue turning even when there is no food left in the hopper. If this happens, you can try unplugging the unit for 30 seconds and then plugging it back in.
This should reset the auger and get it working properly again.
Traeger Auger Stops After a Few Minutes
If your Traeger pellet grill is shutting down after only a few minutes, there are a few things you can do to troubleshoot the issue. First, check the pellets. If they are old or wet, they may not be igniting properly.
Second, check the auger motor. If it is overheating, it will shut down to prevent damage. Lastly, check the controller to make sure it is set to the correct temperature.
If all of these things check out, then you may have a problem with your grill’s igniter rod. This rod is what creates the initial spark that starts the fire in your grill. Over time, it can become corroded and stop working properly.
To clean or replace your igniter rod, consult your owner’s manual for instructions.
Traeger Auger Not Turning Brand New
If you’ve just purchased a brand new Traeger smoker, you may be wondering why the auger isn’t turning. Here’s what you need to know.
The auger is responsible for moving wood pellets from the hopper to the fire pot.
If your auger isn’t turning, it could be because the pellet jam switch is engaged. This switch is designed to shut off the auger if there’s a blockage in the system.
To fix this problem, simply turn off your smoker and clear any obstructions from the hopper or auger tube.
Once you’ve done that, restart your smoker and the auger should start working again.
If you’re still having trouble with your auger, contact Traeger customer service for further assistance.
How Do I Know If My Traeger Auger is Jammed
If you own a Traeger Pellet Grill, you may eventually experience an issue with your auger becoming jammed. This can happen for a variety of reasons, such as if there is a foreign object lodged in the auger tube, or if the auger itself is damaged. If your grill is having trouble feeding pellets into the firepot, it’s likely that the auger is jammed and needs to be cleared.
Here’s how to tell if your auger is jammed, and what you can do to fix it. If your grill isn’t feeding pellets into the firepot as usual, the first thing you should check is the hopper. Make sure that there are pellets in the hopper, and that they’re not clumped together.
Sometimes pellets can get stuck together and jam up the works. If this is the case, simply break them apart with your hands and try again. If there are pellets in the hopper and they’re not clumped together, then it’s likely that the issue is with the auger itself.
To check for a jam, first, make sure that there’s no pellet in front of or behind the auger blade. Then spin the blade by hand – it should spin freely without catching on anything. If it doesn’t spin freely, or if you feel resistance when spinning it, then there’s probably something caught in the blade and you’ll need to clear it out before proceeding further.
The easiest way to clear a jammed auger is to use a wooden dowel or chopstick. Insert one end of the dowel into the hole at the top of the auger (where pellets drop down ), and wiggle it around until you feel it catch on to something solid. Once you’ve found the obstruction, simply pull it out with the dowel.
You may also need to clear out any debris that has fallen into the bottom of the tube – this can be done by removing the tube cap and emptying out anything that has been collected there. Once you’ve cleared out the obstruction and debris, reassemble everything and give your grill a test run. With any luck, your jamming issue will be resolved and you can get back to grilling!
How Fast Does the Auger Turn on a Traeger
Traeger pellet smokers come with a hopper that stores the pellets until they are needed. The auger is what feeds the pellets from the hopper to the fire pot. The speed at which the auger turns is very important because it controls how fast or slow the pellets are fed into the fire pot.
If the auger turns too slowly, the pellets will smolder and produce little smoke. If it turns too quickly, the pellets will ignite and create a lot of smoke. There is a sweet spot in terms of speed, and Traeger pellet smokers are designed to turn at just the right speed to produce optimum results.
Traeger Auger Jam
If you own a Traeger smoker, you may have experienced an auger jam at some point. This can be a frustrating problem, but fortunately, there are some things you can do to fix it. First, check the auger motor to make sure it is receiving power.
If the motor is not receiving power, check the fuse or circuit breaker. Next, inspect the auger gearbox for damage. If the gearbox is damaged, it will need to be replaced.
If the auger motor and gearbox are both in working order, the problem may be with the pellet feed system. Inspect the pellet hopper and feed tube for blockages. Clear any blockages that you find and see if that fixes the problem.
If your Traeger still won’t feed pellets after checking all of these things, call customer service for assistance. They may be able to help you troubleshoot the problem over the phone or they may send someone out to take a look at your smoker in person.
Frequently Asked Questions (FAQs):
Does the Traeger Auger Runs Continuously?
No, the Traeger auger runs for a set period of time then shuts off.
Why is My Traeger Auger Not Turning?
If your Traeger auger isn’t turning, it could be for a number of reasons. The most common reason is that the auger motor has burned out. Other possible causes include a clogged or jammed auger, a faulty switch or wiring, or an issue with the controller.
If you’ve ruled out all of these other potential problems, then it’s likely that the auger motor is to blame. The good news is that replacing the auger motor is relatively easy and shouldn’t take more than a few minutes. Simply remove the old motor and install the new one in its place.
Make sure to double-check all of the connections before turning on your Traeger again. With any luck, this should fix the problem and get your smoker up and running smoothly once again!
Is Traeger Auger Automatic?
Most Traeger grills have an automatic auger that regulates the amount of pellets fed into the fire pot. This prevents the fire from getting too hot or going out. You can usually adjust the settings on the control panel to make the auger feed more or less pellets.
How Do You Know If Your Traeger Auger Motor is Bad?
If your Traeger auger motor is bad, you will likely notice that your grill is not igniting properly or that the pellets are not being fed into the fire pot correctly. In some cases, you may even hear a strange noise coming from the auger motor itself. If you suspect that your auger motor is failing, it’s important to take action quickly in order to avoid any further damage to your grill.
Conclusion
The blogger begins by asking if anyone else has had trouble with their Traeger auger not turning. They say they’ve contacted customer service and were told to check the switch, which they did, but it didn’t fix the problem. Next, they tried unplugging it and plugging it back in, which also didn’t work.
After that, they tried cleaning the burn pot thinking there might be something blocking the auger, but that didn’t help either. Finally, they contacted customer service again and were told to try a hard reset by disconnecting the power cord for 30 seconds and then plugging it back in. That worked!
The blogger concludes by saying that hopefully this information will help someone else who is having the same issue.